Workshop Solutions - Workshop

Workshop Solutions

Ask an expert

Workshop solutions and cleaning

As a rescuer, we know your job doesn’t end when the rescue is finished. For this reason, we support you with tailormade services and workshop solutions for optimised workflow and equipment maintenance. This assists you to reduce your overall cost of ownership while getting the most out of your budget.

How it works

3D drawing of workshop at concept stage

Planning: We plan your workshop in accordance with your requirements. Providing 3D drawings, we enable you to see your workshop at the concept stage, assisting you with selecting suitable components.

Realisation: We offer full installation, commissioning and ongoing service for your workshop

Handover: You’ll receive training for technical equipment, such as washing machines or dryers. We leave the workshop ready for your use and you can start your work immediately.

An introduction to cleaning

The Principals of Equipment Cleaning

Firefighting equipment is useless if it’s not properly cleaned. But, what is the difference between cleaning and disinfection? What determines a safe and effective cleaning process? Get the answers to these questions and learn the four parameters that determine cleaning performance in this video and check out our cleaning posters in the downloads section. 

The Effectiveness of Cleaning Methods

Fire equipment cleaning methods vary greatly around the world. Dräger fire services teamed up with experts in the industry to test differing processes and identify the best cleaning procedures and agents for use with Dräger equipment.

Cleaning_Brochure_4-3.jpg

Curățarea profesională a echipamentelor individuale de protecție ale pompierilor

Chiar dacă flăcările au fost stinse, aceste substanțe rămân în funinginea și în vaporii depuși pe echipamentele de protecție și le contaminează. Aflati mai multe despre riscurile pentru sanatate care apar asociate si cum puteti indeparta substantele periculoase cu solutiile potrivite pentru o abordare adecvata de curatare.

Descarcati brosura

Follow the 6 steps of the cleaning circle

Step 1 - Inbound logistics and registration of contaminated equipment

After an incident all contaminated fire fighters personal protective equipment is transported in closed containers to the professional workshop service. The task: Offloading, registration, and validation of approval of cylinders and then forwarding all delivered items to the first station in the workshop cycle.

Step 2 - Breathing apparatus cleaning and drying

Follow the step-by-step process, starting with the manual pre-washing of the backplate assembly, than the machine cleaning with the pressurized pneumatics preventing water ingress, and final drying phase.  Service technicians should wear appropriate breathing and body protection to avoid indirect contamination doing this work.

Step 3 - Full face masks cleaning and drying

Full face mask are contaminated 2-fold, from the incident site and also by the wearer himself by his body fluids. Therefore the cleaning of the full face mask has also an hygienic term. Learn how this works without health risks for the technician, supported by a modern workshop system.

Step 4 - Cylinder filling room

Follow the process of refilling the breathing air cylinders with respiratory gas, using a filling panel, quick connections and an air quality monitoring system. Refilled cylinders are approved, sealed and marked as “filled”. Doing so, the cylinder is ready again to merge with a SCBA for the next use.

Step 5 - Testings and reconditioning

After completion of the cleaning and drying process, the equipment is transferred to the clean area of the service workshop. The step by step process continues with the reassembling of mask, LDV and backplates. Afterwards the components are tested on an automated test bench supported by documentation software.

Step 6 - Outbound tracking and logistics

Prior to transport back to the fire station all cleaned fire PPE has to be identified, registered, sealed and packed for safe shipment. The registration and documentation for later tracking can effectively be done with a scanner. A workshop software solution collects all information for seamless documentation.

Modern Workshop Design Interview

Being ready for an emergency starts with a suitable workshop layout, with the separation of “dirty” and “clean” areas. Take a look at how our PPE maintenance processes can help. They are supported by cleaning & drying equipment, automated test equipment and asset management. In addition, practical recommendations and solutions reduce service technicians exposure to hazardous substances and ensure efficient and effective cleaning.

Downloads

modern-work-shop-preview.jpg
How to make your cleaning job a safe job

Modern workshop design supports safe cleaning processes for workshop technicians. Our info poster shows the relevant steps at a glance.

Download poster

Cleaning-PDF-Cover-9-11.jpg
4 parameters that determine cleaning effectiveness

These parameters, so called the ‘Sinner’s circle,’ were developed in 1959. The four parameters are variable and can be combined depending on the degree of the contamination of the contaminated surface and on available resources.

Download infographic

Respiratory protection workshop infosheet
Complete respiratory protection workshop

We deliver the full service. Take a detailed look at how we plan your respiratory protection workshop in accordance with your requirements, supply all components and hand over your new workshop ready for use.

Download infosheet

Servicing and care of protective equipment brochure
Quality servicing and care of protective equipment

We supply workshop systems designed to your individual needs which ensure efficient workflow, great care and servicing of your protective equipment.

Download brochure

Related Solutions

firefighters-in-danger-3-2-d-932-2014.jpg

Fire Services Safety Solutions

We know the challenges you face every day. That's why we're here, protecting you every step of the way.

ES-FireTraining-Card.jpg

Fire Service Training Systems

To find out more about our Engineered Solutions for Fire Training Systems click here

luați legătura cu Dräger

Contactați-ne Siguranță

Draeger Romania SRL

Str. Daniel Danielopolu Nr. 42A, Sector 1

014134 București

+40 (0) 21 250 91 68

Sunați-ne de Luni - Joi 8:30 - 17:30

Vineri 8:30 - 12:30